Testing method used to inspect welds, pipes, and structures for defects without damaging the material. Subcontractors performing NDE must hold recognised certifications such as CGSB or ASNT. Clients often require NDE sign-off before authorising progress payments or work acceptance.
NDE (Non-destructive Examination)
Related Terms
Chemical Containment
CompliancePhysical barriers and systems used to prevent hazardous chemicals from spilling into the surrounding environment on a job site. Subcontractors are often responsible for supplying and maintaining containment berms, drip trays, and secondary liners. Failure to meet containment standards can result in site removal or regulatory fines.
TRIIPP (Temperature-related Injury and Illness Prevention Plan)
ComplianceA documented safety plan addressing heat stress and cold exposure risks for workers in outdoor or industrial environments. Subcontractors may be required to submit a TRIIPP before mobilising crews to remote or extreme-climate worksites. It typically outlines monitoring procedures, acclimatisation schedules, and emergency response protocols.
Fall Protection
ComplianceSafety systems and equipment that prevent workers from falling at heights above 3 metres. Subcontractors are responsible for supplying compliant gear and training before mobilising crews to site. Non-compliance can result in stop-work orders and contract liability.
Willful Violation
ComplianceA deliberate breach of a safety regulation or worksite rule, where the subcontractor knew the requirement and chose to ignore it. Regulators treat these far more severely than accidental non-compliance. Fines, stop-work orders, or contract termination can follow.
Ground Disturbance
ComplianceAny activity that breaks soil, such as excavating, grading, or driving stakes. Subcontractors must obtain utility locates and permits before starting work. Skipping this step risks fines and liability for damaged lines.
Well Barrier
ComplianceA physical or mechanical system that prevents uncontrolled flow of fluids from a wellbore. Subcontractors working on or near wells must verify barriers are in place before starting work. Barrier failures can trigger stop-work obligations and regulatory reporting requirements.
Latest Compliance News
Aging NDE Inspector Pool Puts Turnarounds and QC Sign-Offs at Risk
Inspectioneering Journal warns that thin margins and high turnover among NDE contractors are producing certified but underqualified examiners, raising the risk of rework, delays, and missed defects at refineries and chemical plants.
2 months agoComplianceWashington Eyes New Certification Rules for Forklifts Lifting Suspended Loads
Washington's L&I is drafting rule changes clarifying when forklift operators need crane-level certification for suspended loads, following a contractor petition over the state's August 2025 crane rule update.
3 months agoComplianceCSB Report: Undersized Pressure Relief System Caused Fatal 2024 Reactor Explosion
The Chemical Safety Board's final report on a November 2024 explosion at a Louisville chemical facility found an undersized emergency pressure relief system contributed to two worker deaths. The findings carry direct implications for industrial maintenance subcontractors working around pressurized vessels.
5 months agoComplianceLabor Department Proposes Rollback of Biden Independent Contractor Rule
Trump administration seeks to reverse 2024 regulation that made it harder to classify workers as independent contractors, potentially easing compliance burden for construction subcontractors.
8 months agoRelated Guides
How to Read and Negotiate an Oilfield Master Service Agreement (MSA): A Subcontractor's Guide
Learn which MSA clauses actually matter for oilfield subcontractors: indemnity, insurance, payment terms, and change orders. Know what you're signing.
Compliance GuideWhen a Jobsite Incident Happens: What Field Workers Need to Know Before Signing Anything
What to do after a jobsite injury or incident, what your rights are before signing incident reports, how workers' compensation works, and how to protect yourself on multi-employer worksites.
Compliance GuideOSHA Citations on Multi-Employer Worksites: What Subcontractors Need to Know
Learn how OSHA's multi-employer citation policy works, why subcontractors get cited for hazards they didn't create, and how to protect your company on operator-controlled job sites.
Stay sharp on field operations
Industry news and insights, delivered to your inbox.
Subscribe to FieldNews
